document.write (''); document.write ('');

您当前的位置:首页 » 供应 » 其他 » 其他
prev next
  • 型 号:ECI 1010
  • 规 格:1磅/罐
  • 品 牌:LOCTITE
  • 单 价:100.00元/罐
  • 供货总量:10000 罐
  • 最小起订量:10 罐
  • 有效期至:2017-09-12
  • 发货期限:付款之日起3天内发货
  • 最后更新:2016-09-12
  • 浏览次数:0

询价

订购

qg988钱柜娱乐详情

 供应乐泰导电银浆LOCTITE ECI 1010
PRODUCT DESCRIPTION
LOCTITE ECI 1010 E&C provides the following product
characteristics:
Technology Thermoplastic
Appearance Gray paste
Filler Type Silver
Product Benefits ● Flexible
● Good adhesion
● High conductivity
Operating Temperature-
Maximum
100ºC
Cure Hot air drying
Application Conductive Ink
Typical Assembly
Applications
Flexible printed circuits, RFID and other
conductive circuits
Key Substrates PET substrates
LOCTITE ECI 1010 E&C is a screen printable, conductive ink .
TYPICAL PROPERTIES OF UNCURED MATERIAL
Solids Content (TGA), % 62
Density, g/ml 2.1
Viscosity @ 1.5 s-1 , Rheometer, mPa∙s (cP) 9,000
Thixotropic Index (15/1.5 s-1 ) 1.9
Theoretical coverage @ 10 μm dry film thickness,
m²/kg
10.6
Shelf Life @ 2 to 8°C (from date of manufacture),
days
180
Flash Point - See SDS
TYPICAL CURING PERFORMANCE
Recommended Drying Cycle
15 minutes @ 120°C or
2minutes @ 150°C
LOCTITE ECI 1010 E&C can be dried using forced air or infrared
systems. Higher temperatures for longer time exposure will improve
the performance. Care should be taken with infrared. Too much
energy can destroy the coating. Design drying rates for the maximum
the substrate and production speeds can tolerate.
The above drying profile is a guideline recommendation. Conditions
(time and temperature) may vary based on customers' experience
and their application requirements, as well as customer drying
equipment, oven loading and actual oven temperatures.
TYPICAL PROPERTIES OF CURED MATERIAL
Physical Properties
Adhesion , Cross Hatch, grade 5B
Electrical Properties
Sheet Resistance , ohm/sq/25 μm 0.007
GENERAL INFORMATION
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
DIRECTIONS FOR USE
1. Surface Preparation
● Clean surface thoroughly prior to application.
2. Mixing/Dilution
● Mix thoroughly before use to ensure it is homogenous. A slow
speed propeller may be utilized to mix until product is uniform.
● If needed, the ink can be diluted with Butyl glycol acetate.
3. Application
● LOCTITE ECI 1010 E&C may be applied by screen printing
method.
● Recommended screen and printing parameters are:
Screen Type Polyester screen
Screen mesh 160 to 200 mesh
Emulsion Thickness , μm 10 to 40
Squeegee Hardness 70 to 90
Clean-up
1. The equipment can be cleaned with esters (butylacetate,
ethylacetate) or ketones (MIBK, MEK).
Storage
Store product in the unopened container in a dry location. Storage
information may be indicated on the product container labeling.
Optimal Storage: 2 to 8°C. Storage below 0°C or above 30°C can
adversely affect product properties.
Material removed from containers may be contaminated during use.
Do not return product to the original container. Henkel Corporation
cannot assume responsibility for product which has been contaminated
or stored under conditions other than those previously indicated. If
additional information is required, please contact your local Technical
Service Center or Customer Service Representative.
Not for product specifications
The technical data contained herein are intended as reference only.
Please contact your local quality department for assistance and
recommendations on specifications for this product.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
N x 0.225 = lb
N/mm x 5.71 = lb/in
psi x 145 = N/mm²
MPa = N/mm²
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP可提供样品技术支持 有意者电联

供应商的其他相关信息

查看该供应商更多供应qg988钱柜娱乐

免责声明:以上所展示的信息由会员自行提供,内容的真实性、准确性和合法性由发布会员负责。中国www.qg988.com对此不承担任何责任。

友情提醒:为规避购买风险,建议您在购买相关qg988钱柜娱乐前务必确认供应商资质及qg988钱柜娱乐质量!

公司基本资料信息


  • 深圳汉泰实业有限公司
  • 联系人:杨振   
  • 电   话:
  • 手   机:
  • 地   区:广东 深圳市
  • 地   址:广东深圳福田爱地大厦